add environment examples with sensors

docs/software/plugins/environment.md

@@ -85,6 +85,99 @@ The device must be restarted after the settings have been changed for the plugin
 
 The sensors can be wired differently, here's one example for sensor DS18B20 https://randomnerdtutorials.com/esp32-ds18b20-temperature-arduino-ide
 
+## Example of T-LoraV1 with DHT22 temperature sensor
+
+Setup of a T-LoraV1 with DHT22 temperature sensor.
+
+[<img src="T-LoraV1 with DHT22" src="/img/hardware/lora_v1_with_DHT22.jpg" style={{zoom:'25%'}} />](/img/hardware/lora_v1_with_DHT22)
+
+Requirements:
+* T-LoraV1 (but any esp32 should work, just be sure to double check which GPIO to use)
+* DHT22 sensor
+* 10 Kohm resistor (optional, but recommended)
+* breadboard (optional)
+* two red wires (could be a different color, but 5V is typically red)
+* two yellow wires for GPIO (could be a different color)
+* one black wire (could be a different color, but GROUND is typically black)
+
+Steps:
+* disconnect power/battery
+* connect black wire from GROUND to "-" on the DHT22
+* connect yellow wire from middle PIN to a row on bread board
+* connect red wire from 5V to a row on breadboard
+* connect resistor between red and yellow rows
+* connect red wire from row with red to "+" on DHT22
+* connect yellow wire from yellow row to GPIO on device (ex: GPIO21)
+* double check the cabling (if you get it wrong, you can damage the device and/or the DHT22 sensor)
+* plug in device
+* configure the device:
+
+```
+meshtastic --set environmental_measurement_plugin_measurement_enabled true --set environmental_measurement_plugin_screen_enabled true --set environmental_measurement_plugin_update_interval 15 --set environmental_measurement_plugin_display_farenheit true --set environmental_measurement_plugin_sensor_type DHT22 --set environmental_measurement_plugin_sensor_pin 21
+```
+
+:::tip
+You can change the values above to suit your needs. The commands can be run one at a time or in a group as show above.
+:::
+
+* reboot/reset the device (press the RST button or unplug/plug in the device)
+* when the device boots it should say "Environment" and it may show the sensor data
+* if "no data", then triple check the wiring
+* if still "no data", run:
+
+```
+meshtastic --info
+```
+
+and verify the the environmental_measurement_plugin_sensor_type and environmental_measurement_plugin_sensor_pin
+
+
+## Example of T-LoraV1 with Dallas DS18B20 temperature sensor
+
+Setup of a T-LoraV1 with DS18B20 temperature sensor.
+
+[<img src="T-LoraV1 with DS18B20" src="/img/hardware/lora_v1_with_DS18B20.jpg" style={{zoom:'25%'}} />](/img/hardware/lora_v1_with_DS18B20)
+
+Requirements:
+* T-LoraV1 (but any esp32 should work, just be sure to double check which GPIO to use)
+* DS18B20 sensor
+* 10 Kohm resistor (optional, but recommended)
+* breadboard (optional)
+* two red wires (could be a different color, but 5V is typically red)
+* two yellow wires for GPIO (could be a different color)
+* one black wire (could be a different color, but GROUND is typically black)
+
+Steps:
+* disconnect power/battery
+* connect black wire from GROUND to "-" on the DS18B20
+* connect yellow wire from DAT pin to a row on bread board
+* connect red wire from 5V to a row on breadboard
+* connect resistor between red and yellow rows
+* connect red wire from row with red to "VCC" on DS18B20
+* connect yellow wire from yellow row to GPIO on device (ex: GPIO21)
+* double check the cabling (if you get it wrong, you can damage the device and/or the sensor)
+* plug in device
+* configure the device:
+
+```
+meshtastic --set environmental_measurement_plugin_measurement_enabled true --set environmental_measurement_plugin_screen_enabled true --set environmental_measurement_plugin_update_interval 15 --set environmental_measurement_plugin_display_farenheit true --set environmental_measurement_plugin_sensor_type DS18B20 --set environmental_measurement_plugin_sensor_pin 21
+```
+
+:::tip
+You can change the values above to suit your needs. The commands can be run one at a time or in a group as show above.
+:::
+
+* reboot/reset the device (press the RST button or unplug/plug in the device)
+* when the device boots it should say "Environment" and it may show the sensor data
+* if "no data", then triple check the wiring
+* if still "no data", run:
+
+```
+meshtastic --info
+```
+
+and verify the the environmental_measurement_plugin_sensor_type and environmental_measurement_plugin_sensor_pin
+
 
 ## Known Problems