mirror of
https://github.com/meshtastic/meshtastic.git
synced 2024-09-20 08:07:33 -07:00
Merge branch 'master' into serial-adapter-01
This commit is contained in:
Ben Meadors
GitHub
commit
21a855f4c4
|
|
@ -62,17 +62,7 @@ To ensure devices with different PRIMARY channel name transmit on the same frequ
|
|||
|
||||
## Channel Settings Values
|
||||
|
||||
The Channel Settings options are: ID, Name, PSK, Downlink Enabled, and Uplink Enabled. Channel settings are embedded in the `Channel` protobuf as a `ChannelSettings` protobuf and sent as an admin message.
|
||||
|
||||
:::note
|
||||
The full globally unique ID will be constructed from the Name and ID (`<name>.<id>`) where ID is base36 encoded. Assuming that the number of Meshtastic users is below 20K (true for a long time) the chance of this 64 bit random number colliding with anyone else is super low. The penalty for collision is low as well.
|
||||
:::
|
||||
|
||||
### ID
|
||||
|
||||
Used to construct a globally unique channel ID.
|
||||
|
||||
Set to `0` by default.
|
||||
The Channel Settings options are: Name, PSK, Downlink Enabled, and Uplink Enabled. Channel settings are embedded in the `Channel` protobuf as a `ChannelSettings` protobuf and sent as an admin message.
|
||||
|
||||
### Name
|
||||
|
||||
|
|
@ -103,6 +93,8 @@ If enabled, messages from the mesh will be sent to the **public** internet throu
|
|||
|
||||
Set to `false` by default for all channels.
|
||||
|
||||
## Examples
|
||||
|
||||
<Tabs
|
||||
groupId="settings"
|
||||
defaultValue="cli"
|
||||
|
|
@ -162,11 +154,6 @@ meshtastic --ch-set name "My Channel" --ch-set psk random --ch-set uplink_enable
|
|||
|
||||
:::
|
||||
|
||||
### Id
|
||||
|
||||
```shell title="Set the PRIMARY channel ID"
|
||||
meshtastic --ch-set id 1234 --ch-index 0
|
||||
```
|
||||
|
||||
### Name
|
||||
|
||||
|
|
|
|||
|
|
@ -12,6 +12,8 @@ The Canned Message Module will allow you to send messages to the mesh network fr
|
|||
|
||||
The canned message module config options are: Enabled, Save, and Sender. Range Test Module config uses an admin message sending a `ConfigModule.CannedMessage` protobuf.
|
||||
|
||||
<object data="https://www.youtube.com/embed/qKQVYUbLLkg?autohide=1&autoplay=0" width="100%" height="400"></object>
|
||||
|
||||
## Canned Message Module Config Values
|
||||
|
||||
### Enabled
|
||||
|
|
@ -219,9 +221,9 @@ Example: 1|2|3||5|6|7||9|10|11||13|14|15 - the slots 4,8 and 12 can not be used.
|
|||
|
||||
The CardKB is fully supported in freetext mode and select mode. Use UP/DOWN/ENTER to select a predefined message and send it. For a freetext message, just type it in and press ENTER to send it.
|
||||
|
||||
If you don't want to broadcast your freetext message, you can use the CardKB to send it to a specific node. Just press TAB and select the target node with the LEFT/RIGHT keys. The message will be sent to the node with the matching name and node number. The target node will be remebered for your nexxt message.
|
||||
If you don't want to broadcast your freetext message, you can use the CardKB to send it to a specific node. Just press TAB and select the target node with the LEFT/RIGHT keys. The message will be sent to the node with the matching name and node number. The target node will be remembered for your next message.
|
||||
|
||||
### 3 Buttun up/down and RAK rotary encoder
|
||||
### 3 Button up/down and RAK rotary encoder
|
||||
|
||||
Just use UP/DOWN/ENTER to select a predefined message and send it.
|
||||
|
||||
|
|
|
|||
|
|
@ -22,7 +22,7 @@ The [T-Beam 0.7](/docs/hardware/devices/tbeam#t-beam---v07) board is an earlier
|
|||
:::
|
||||
|
||||
## Command Line Interface Instructions
|
||||
|
||||
### Install Prerequisite Software
|
||||
<Tabs
|
||||
groupId="operating-system"
|
||||
defaultValue="linux"
|
||||
|
|
@ -33,7 +33,6 @@ values={[
|
|||
]}>
|
||||
<TabItem value="linux">
|
||||
|
||||
### Install Prerequisite Software
|
||||
|
||||
Check if you have `python3` and `pip` installed with the following command
|
||||
|
||||
|
|
@ -53,18 +52,12 @@ If `pip` is not installed, install with
|
|||
|
||||
```shell
|
||||
sudo apt-get install python3-pip
|
||||
```
|
||||
|
||||
### Install `esptool`
|
||||
|
||||
```shell
|
||||
pip3 install --upgrade esptool
|
||||
```
|
||||
|
||||
</TabItem>
|
||||
<TabItem value="macos">
|
||||
|
||||
### Install Prerequisite Software
|
||||
|
||||
|
||||
OS X comes with `Python 2.7` installed, but not `pip`. The following uses Homebrew to install `python3` which includes `pip3`. On MacOS you will use `pip3` instead > of `pip`.
|
||||
|
||||
|
|
@ -96,12 +89,6 @@ Confirm `pip3` was installed alongside `python3`
|
|||
|
||||
```shell
|
||||
pip3 -v
|
||||
```
|
||||
|
||||
### Install `esptool`
|
||||
|
||||
```shell
|
||||
pip3 install --upgrade esptool
|
||||
```
|
||||
|
||||
</TabItem>
|
||||
|
|
@ -123,15 +110,17 @@ pip --version
|
|||
|
||||
:::
|
||||
|
||||
### Install `esptool`
|
||||
|
||||
```shell
|
||||
pip install --upgrade esptool
|
||||
```
|
||||
|
||||
</TabItem>
|
||||
</Tabs>
|
||||
|
||||
### Install `esptool`
|
||||
|
||||
```shell
|
||||
pip3 install --upgrade esptool
|
||||
```
|
||||
|
||||
|
||||
### Confirm Communication With Chip
|
||||
|
||||
<Tabs
|
||||
|
|
|
|||
Loading…
Reference in a new issue