add more info about env sensors

docs/software/plugins/environment.md

@@ -5,7 +5,9 @@ sidebar_label: Environment measurement
 ---
 ## About
 
-The Environment Measurement Plugin will allow nodes to send a specific message with information from connected environmental sensors. Currently supported sensors are DHT11 and Dallas 1-wire DS18B20. This plugin does only work on ESP32 devices.
+The Environment Measurement Plugin will allow nodes to send a specific message with information from connected environmental sensors. Currently supported sensors are BME280, BME680, DHT11, DHT12, DHT21, DHT22 and Dallas 1-wire DS18B20.
+
+The preferred setup is using I2C, so the `environmental_measurement_plugin_sensor_pin` may not be needed.
 
 ## Configuration
 
@@ -13,7 +15,7 @@ These are the settings that can be configured.
 
     environmental_measurement_plugin_enabled
         Is the plugin enabled?
-        
+
         0 = Disabled (Default)
         1 = Enabled
 
@@ -40,21 +42,26 @@ These are the settings that can be configured.
 
     environmental_measurement_plugin_display_fahrenheit
         Should temperature readings be converted to fahrenheit?
-    
+
         0 = Disabled (Default)
         1 = Enabled
-        
+
     environmental_measurement_plugin_sensor_type
         What sensor is connected?
-        
+
         0 = DHT11 (Default)
         1 = Dallas 1-wire DS18B20
-        
+        2 = DHT12
+        3 = DHT21
+        4 = DHT22
+        5 = BME280
+        6 = BME680
+
     environmental_measurement_plugin_sensor_pin
         Which pin is the sensor connected to?
-        
+
         Default = 0
-    
+
 
 ## Usage Notes
 
@@ -63,22 +70,22 @@ For basic usage, start with:
 	environmental_measurement_plugin_enabled = 1
 
 	environmental_measurement_plugin_screen_enabled = 1
-    
+
 Depending on which pin your sensor is connected to, set it accordingly:
 
 	environmental_measurement_plugin_sensor_pin = 13
-  
+
 
 :::note
 The device must be restarted after the settings have been changed for the plugin to take effect.
 :::
-	
+
 
 ## Hardware
 
 The sensors can be wired differently, here's one example for sensor DS18B20 https://randomnerdtutorials.com/esp32-ds18b20-temperature-arduino-ide
 
-    
+
 ## Known Problems
 
 * No default configuration values are currently set, so this must be done when enabling the plugin.

docs/software/settings/environmental-measurment-plugin.md

@@ -9,11 +9,7 @@ import TabItem from '@theme/TabItem';
 
 ## Overview
 
-:::caution
-This is a work in progress and is not yet available.
-:::
-
-The Environmental Measurement Plugin will allow you to connect climate sensors to report local conditions to your mesh.
+The Environmental Measurement Plugin will allow you to connect environment sensors to report conditions to your mesh. Examples are temperature, humidity and gas pressure.
 
 ## Settings
 
@@ -50,7 +46,7 @@ Enable/Disable the environmental measurement plugin on-device display.
 
 ### environmental_measurement_plugin_sensor_pin
 
-Specify the preferred GPIO Pin for sensor readings.
+Specify the preferred GPIO Pin for sensor readings. May not be needed if using I2C.
 
 ### environmental_measurement_plugin_sensor_type
 
@@ -72,15 +68,32 @@ Interval in seconds of how often we should try to send our measurements to the m
   values={[
     {label: 'CLI', value: 'cli'},
     {label: 'Android', value: 'android'},
+    {label: 'iOS', value: 'iOS'},
+    {label: 'web', value: 'web'},
   ]}>
   <TabItem value="cli">
 
-  TODO
+meshtastic --set environmental_measurement_plugin_measurement_enabled true
+meshtastic --set environmental_measurement_plugin_screen_enabled true
+meshtastic --set environmental_measurement_plugin_update_interval 15
+meshtastic --set environmental_measurement_plugin_display_farenheit true
+meshtastic --set environmental_measurement_plugin_sensor_type 5
+meshtastic --set environmental_measurement_plugin_sensor_type BME280
 
   </TabItem>
   <TabItem value="android">
 
   TODO
 
+  </TabItem>
+  <TabItem value="iOS">
+
+  TODO
+
+  </TabItem>
+  <TabItem value="web">
+
+  TODO
+
   </TabItem>
 </Tabs>