diff --git a/docs/configuration/module-config/canned-message.mdx b/docs/configuration/module-config/canned-message.mdx
index a040d13f..72161cea 100644
--- a/docs/configuration/module-config/canned-message.mdx
+++ b/docs/configuration/module-config/canned-message.mdx
@@ -12,6 +12,8 @@ The Canned Message Module will allow you to send messages to the mesh network fr
 
 The canned message module config options are: Enabled, Save, and Sender. Range Test Module config uses an admin message sending a `ConfigModule.CannedMessage` protobuf.
 
+<object data="https://www.youtube.com/embed/qKQVYUbLLkg?autohide=1&autoplay=0" width="100%" height="400"></object>
+
 ## Canned Message Module Config Values
 
 ### Enabled
@@ -219,9 +221,9 @@ Example: 1|2|3||5|6|7||9|10|11||13|14|15 - the slots 4,8 and 12 can not be used.
 
 The CardKB is fully supported in freetext mode and select mode. Use UP/DOWN/ENTER to select a predefined message and send it. For a freetext message, just type it in and press ENTER to send it.
 
-If you don't want to broadcast your freetext message, you can use the CardKB to send it to a specific node. Just press TAB and select the target node with the LEFT/RIGHT keys. The message will be sent to the node with the matching name and node number. The target node will be remebered for your nexxt message.
+If you don't want to broadcast your freetext message, you can use the CardKB to send it to a specific node. Just press TAB and select the target node with the LEFT/RIGHT keys. The message will be sent to the node with the matching name and node number. The target node will be remembered for your next message.
 
-### 3 Buttun up/down and RAK rotary encoder
+### 3 Button up/down and RAK rotary encoder
 
 Just use UP/DOWN/ENTER to select a predefined message and send it.
 
diff --git a/docs/getting-started/flashing-firmware/esp32/cli-script.mdx b/docs/getting-started/flashing-firmware/esp32/cli-script.mdx
index c5f18fba..51bbade3 100644
--- a/docs/getting-started/flashing-firmware/esp32/cli-script.mdx
+++ b/docs/getting-started/flashing-firmware/esp32/cli-script.mdx
@@ -22,7 +22,7 @@ The [T-Beam 0.7](/docs/hardware/devices/tbeam#t-beam---v07) board is an earlier
 :::
 
 ## Command Line Interface Instructions
-
+### Install Prerequisite Software
 <Tabs
 groupId="operating-system"
 defaultValue="linux"
@@ -33,7 +33,6 @@ values={[
 ]}>
 <TabItem value="linux">
 
-### Install Prerequisite Software
 
 Check if you have `python3` and `pip` installed with the following command
 
@@ -53,18 +52,12 @@ If `pip` is not installed, install with
 
 ```shell
 sudo apt-get install python3-pip
-```
-
-### Install `esptool`
-
-```shell
-pip3 install --upgrade esptool
 ```
 
   </TabItem>
   <TabItem value="macos">
 
-### Install Prerequisite Software
+
 
 OS X comes with `Python 2.7` installed, but not `pip`. The following uses Homebrew to install `python3` which includes `pip3`. On MacOS you will use `pip3` instead > of `pip`.
 
@@ -96,12 +89,6 @@ Confirm `pip3` was installed alongside `python3`
 
 ```shell
 pip3 -v
-```
-
-### Install `esptool`
-
-```shell
-pip3 install --upgrade esptool
 ```
 
   </TabItem>
@@ -123,15 +110,17 @@ pip --version
 
 :::
 
-### Install `esptool`
-
-```shell
-pip install --upgrade esptool
-```
 
   </TabItem>
 </Tabs>
 
+### Install `esptool`
+
+```shell
+pip3 install --upgrade esptool
+```
+
+
 ### Confirm Communication With Chip
 
 <Tabs