From 3601b414cf0ec039bbe6f8cb521f3e2bb1c49cda Mon Sep 17 00:00:00 2001 From: apt105 <73254487+apt105@users.noreply.github.com> Date: Sun, 9 May 2021 14:51:23 +0100 Subject: [PATCH 1/3] Antennas --- website/docs/hardware/antenna.md | 150 -------------------- website/docs/hardware/antenna/aerials.md | 45 ++++++ website/docs/hardware/antenna/antenna.md | 39 +++++ website/docs/hardware/antenna/non-aerial.md | 24 ++++ website/docs/hardware/antenna/resources.md | 46 ++++++ website/docs/hardware/antenna/testing.md | 33 +++++ website/docs/software/plugins/plugin-api.md | 0 website/sidebars.js | 10 +- 8 files changed, 196 insertions(+), 151 deletions(-) delete mode 100644 website/docs/hardware/antenna.md create mode 100644 website/docs/hardware/antenna/aerials.md create mode 100644 website/docs/hardware/antenna/antenna.md create mode 100644 website/docs/hardware/antenna/non-aerial.md create mode 100644 website/docs/hardware/antenna/resources.md create mode 100644 website/docs/hardware/antenna/testing.md create mode 100644 website/docs/software/plugins/plugin-api.md diff --git a/website/docs/hardware/antenna.md b/website/docs/hardware/antenna.md deleted file mode 100644 index 0218fe31..00000000 --- a/website/docs/hardware/antenna.md +++ /dev/null @@ -1,150 +0,0 @@ ---- -id: antenna -title: Antennas -sidebar_label: Antennas -slug: /hardware/antenna ---- - -## TL; DR - -If you have sufficient range with your existing aerial, skip this section. If you don't, consider either getting more nodes and / or replace the stock aerial with one tuned (to your region transmitter's frequency): - -- A quarter quarter wave _tuned_ stubby aerial (<10cm for fit-in-pocket) should have a real-world range of a couple of km without significant obstacles (buildings / hills). -- Aerial criteria: 50 Ohm, SMA male connector, low VSWR (<2) (at tuning frequency - see its datasheet), gain > 0 dbi . -- Caution, avoid suppliers who: - - don't state the aerial's tuned frequency and its specific purpose (LoRa network) - - claim huge gain figures on omni-directional aerials - - don't provide boringly professional data-sheets. -- If you want more range, directionality, specificity read on. - -## General guidance - -The Meshtastic system is designed to be simple and intuitive to use. However, its LoRa radios rely on point to point communications, unit to unit, aerial to aerial; quite different to the near ubiquitous radio coverage of today's cellphone & wi-fi connections. - -Some understanding of the factors affecting radio communications will help achieve substantially better service, faster transmission, over a greater range with your devices. Here, we'll attempt to provide a top-level set of guidance for use and aerial selection, how to test the aerials, and a set of resources for further research and plenty of opportunity for going deeper. - -The Meshtastic devices (of various flavours) lend themselves to experimentation, not only because you can replace their aerials, but also because of their mesh operation. All nodes will, without alteration, relay communications from any other members of the mesh around obstacles and over greater distances. The cost of aerial investment should be weighed against investment in additional low-cost nodes. - -:::caution -Do not switch on your Meshtastic device (or any other transmitter) without an aerial attached - see below. -::: - -The information collected here is by no means definitive, and necessarily abbreviated (it's a huge topic). - -## Non aerial factors affecting transmission - -Unless you're using your devices in a vacuum with clear line of sight between aerials: -- Weather (temperature, humidity & air pressure), -- Transmission power, spreading and other associated channel factors, -- Number of nodes within reach in the mesh (affects retries consequent duty cycle hit), -- Absorption by materials (with varying degrees attenuation, by material and depth), -- Reflection off surfaces (and channeled through material tunnels, including warm / cold air tunnels commonly present in the atmosphere), -- Diffraction around obstacles (over forests and around corners). - -## Aerial selection - -The stock aerials provided bundled with the t-Beam and other boards are, in general a 'mixed bag'. They may not have been selected for your given frequency range, tuned or of a quality design. - -Matching an aerial to the frequency of transmission is important, as is choosing an appropriate design. - -The aerial's design will affect: -- proportion of the signal which leaves the aerial (efficiency), -- directions in which it's transmitted, and whether it will be affected by horizontal / vertical polarisation, -- proportion of signal which is reflected back within the device itself. - -:::caution -While the LoRa devices we are using for Meshtastic are relatively low power radios, care should be taken _not_ to operate any radio transmission device without an aerial or with a poorly matched aerial. Un-transmitted radio signal reflected back to the transmitter can damage the device. -::: - -### Important considerations: - -- What transmission frequency are you using? (varies by region) - - Devices on another frequency will not be able to interact with yours. - - Only specific frequencies are licensed [radio settings](docs/developers/device/radio-settings). -- How will you be carrying / transporting the radio? - - A large directional aerial will transmit over significantly greater distance than an omni-directional aerial. However, it must be pointed at its target so isn't optimal for mobile use. - - A tuned half wave whip aerial may have more omni-directional range than the quarter wave stubby; but it will be conspicuous in your pocket. -- Do you want transmission in all directions? - - While humans (mostly water) don't attenuate signal greatly (at LoRa frequencies), buildings & walls do. - - If your aerial is permanently positioned against a building, signal transmitted towards the wall will be largely lost. -- Does my Meshtastic device have the right power range, impedance & connector for the aerial? - - For the T-Beam devices it should be 50 Ohm impedance, with SMA connector, many will be recommended for LoRa use in their technical details. - - By contrast, a close range, contact-less Personal Area Network antenna, or a huge aerial at the end of length of coax designed for a 100W transmitter are not going to be operable. -- Cost, quality and supply service? - - The perfect aerial on paper, sourced from the other side of the world with mixed reviews doesn't compare to a local supplier who has spent time carefully collating all of the aerial data-sheets for comparison _and_ holds stock immediately available - personally I prefer to pay significantly more for a time saving, quality service. - -## Terminology / references & further research - -You could also do worse than reading the [wikipedia entry for Antenna](https://en.wikipedia.org/wiki/Antenna_(radio)). - -Instead of repeat listing the terms, let us recommend this superb [tutorial](https://www.youtube.com/watch?v=J3PBL9oLPX8) by Andreas Speiss (the 'guy with the Swiss accent'). - -See in the references of the above LoRa world record transmission distance details & instructions on self-build Moxon antennae. - -### Environmental - -For a bit of light reading on environmental research: - - - [RF attentuation in vegetation](https://www.itu.int/dms_pubrec/itu-r/rec/p/R-REC-P.833-9-201609-I!!PDF-E.pdf) (yes really); if you wander through the woods wondering how your RF is bouncing off leaves dependent on their variety, and wind speed … well you do, now. - - [RF attentuation with various building materials](https://www.ofcom.org.uk/__data/assets/pdf_file/0016/84022/building_materials_and_propagation.pdf). - - This one by ITU again is very detailed in its [analysis of the drivers of attenuation](https://www.itu.int/dms_pubrec/itu-r/rec/p/R-REC-P.2040-1-201507-I!!PDF-E.pdf) (I wasn’t aware that all EMF radiation exhibits reflection / transmission characteristics akin to light hitting a material boundary. So, depending on the angle of incidence, material and the EMF wavelength, it will be reflected and / or transmitted through). - - These RF bands are also made more [noisy by adjacent LTE](https://www.ofcom.org.uk/__data/assets/pdf_file/0023/55922/lte-coexistence.pdf) - -In summary - our wavelengths in Europe fair well in plain sight, curve over not-so-tall obstacles (including trees), reflect of surfaces at low angles of incidence. They go through humans without much attenuation; but not brick or stone or anything much above glass / kevlar. Oh, and don’t sit under an LTE tower and expect it to be plain sailing. - -### Testing - -A [couple](https://medium.com/home-wireless/testing-lora-antennas-at-915mhz-6d6b41ac8f1d) of [excellent](https://medium.com/home-wireless/testing-and-reviewing-lora-antennas-5b37dfa594a3) aerial comparison & testing videos. Their utility goes beyond the specific aerials tested: -- Insight into aerial types & their characteristics, -- Testing approaches. - -On the topic of testing - performing your own testing and providing feedback is the lifeblood of Meshtastic and OpenSource projects. - -Stating the obvious: -- Walk around with a radio sending messages, -- For each message, note location and whether 'ack' ticks are received, -- Also note reported signal strengths, -- Change aerials, repeat & contrast. - -:::note -This can be done by utilising the [range test plugin](/docs/software/plugins/range-test-plugin) -::: - -## Discussion - -To comment on / join in antenna range [Meshtastic discourse](https://meshtastic.discourse.group/t/antenna-improved-range/227/35?u=sens8tion) - -There, you will also find reference to Meshtastic range achievements, aerial recommendations (note we've stopped short of making specific supplier aerial recommendations in this wiki). - -## Resources - -### Coverage prediction - -* [Tower Coverage.com](https://www.towercoverage.com/) - * Commercial but has free options - - -* [HeyWhat'sThat](http://www.heywhatsthat.com/) - * Free with path profiling options - - -* [Radio Mobile Online](https://www.ve2dbe.com/rmonline_s.asp) - * Radio Mobile Online is a radio wave propagation prediction tool dedicated to amateur radio - - -### RF Tools - -* [Times Microwave Systems](https://www.timesmicrowave.com/calculator/?Product=RG-6&RunLength=10&Frequency=868) - * Coaxial Cable Attenuation & Power Handling Calculator - - -* [Solwise Link Budget Calculator](https://www.solwise.co.uk/link-budget.htm) - * Predict the received signal strength - - -### Antenna designs - -* [1/4 Wave Ground Plane Antenna Calculator](https://m0ukd.com/calculators/quarter-wave-ground-plane-antenna-calculator/) - - -* [Quadrifilar helicoidal antenna calculator](https://jcoppens.com/ant/qfh/calc.en.php) diff --git a/website/docs/hardware/antenna/aerials.md b/website/docs/hardware/antenna/aerials.md new file mode 100644 index 00000000..b435909b --- /dev/null +++ b/website/docs/hardware/antenna/aerials.md @@ -0,0 +1,45 @@ +--- +id: aerials +title: Aerial selection +sidebar_label: Aerial selection +slug: /hardware/aerials +--- + +The stock aerials provided bundled with the t-Beam and other boards are, in general a 'mixed bag'. They may not have been selected for your given frequency range, tuned or of a quality design. + +Matching an aerial to the frequency of transmission is important, as is choosing an appropriate design. + +The aerial's design will affect: +- proportion of the signal which leaves the aerial (efficiency), +- directions in which it's transmitted, and whether it will be affected by horizontal / vertical polarisation, +- proportion of signal which is reflected back within the device itself. + +:::caution +While the LoRa devices we are using for Meshtastic are relatively low power radios, care should be taken _not_ to operate any radio transmission device without an aerial or with a poorly matched aerial. Un-transmitted radio signal reflected back to the transmitter can damage the device. +::: + +### Important considerations: + +- What transmission frequency are you using? + - Devices on another frequency will not be able to interact with yours. + - See this listing by [The Things Network](https://www.thethingsnetwork.org/docs/lorawan/frequencies-by-country.html) for frequencies licensed for specific countries. +- How will you be carrying / transporting the radio? + - A large directional aerial will transmit over significantly greater distance than an omni-directional aerial. However, it must be pointed at its target so isn't optimal for mobile use. + - A tuned half wave whip aerial may have more omni-directional range than the quarter wave stubby; but it will be conspicuous in your pocket. + - Many antennas, especially quater wave stubby antennas, require the use of ground planes to transmit at peak performance. +- Do you want transmission in all directions? + - While humans (mostly water) don't attenuate signal greatly (at LoRa frequencies), buildings & walls do. + - If your aerial is permanently positioned against a building, signal transmitted towards the wall will be largely lost. +- Does my Meshtastic device have the right power range, impedance & connector for the aerial? + - For the LoRa devices it should be 50 Ohm impedance, with SMA connector. Many antennas will be recommended for LoRa use in their technical details. + - By contrast, a close range, contact-less Personal Area Network antenna, or a huge aerial at the end of length of coax designed for a 100W transmitter are not going to be operable. +- Cost, quality and supply service? + - The perfect aerial on paper, sourced from the other side of the world with mixed reviews doesn't compare to a local supplier who has spent time carefully collating all of the aerial data-sheets for comparison _and_ holds stock immediately available - personally I prefer to pay significantly more for a time saving, quality service. +- How close will the antenna be to my Meshtastic device? + - Most cables will significantly degrade the signal strength over any significant distance. It is often more effective to place a node outside, than to have it indoors with the antenna outside. + +## Terminology / references + +You could do a lot worse than reading the [Wikipedia entry for Antenna](https://en.wikipedia.org/wiki/Antenna_(radio)), along with the [Wikipedia entry for LoRa](https://en.wikipedia.org/wiki/LoRa). + +Instead of listing the terms, let us recommend this superb [tutorial](https://www.youtube.com/watch?v=J3PBL9oLPX8) by Andreas Speiss (the 'guy with the Swiss accent'). diff --git a/website/docs/hardware/antenna/antenna.md b/website/docs/hardware/antenna/antenna.md new file mode 100644 index 00000000..e1b7c7f9 --- /dev/null +++ b/website/docs/hardware/antenna/antenna.md @@ -0,0 +1,39 @@ +--- +id: antenna +title: Antennas +sidebar_label: Antennas +slug: /hardware/antenna +--- + +## TL; DR + +If you have sufficient range with your existing aerial, skip this section. If you don't, consider either getting more nodes and / or replace the stock aerial with one tuned (to your region transmitter's frequency): + +- A quarter quarter wave _tuned_ stubby aerial (<10cm for fit-in-pocket) should have a real-world range of a couple of km without significant obstacles (buildings / hills). +- Aerial criteria: 50 Ohm, appropriate connector (usually SMA male of U.FL), low VSWR (<2) (at tuning frequency - see its datasheet), gain > 0 dbi . +- Caution, avoid suppliers who: + - don't state the aerial's tuned frequency and its specific purpose (LoRa network) + - claim huge gain figures on omni-directional aerials + - don't provide boringly professional data-sheets. + +If you want more range, directionality, or specificity read on. + +## General guidance + +The Meshtastic system is designed to be simple and intuitive to use. However, its LoRa radios rely on point to point communications, unit to unit, aerial to aerial; quite different to the near ubiquitous radio coverage of today's cellphone & wi-fi connections. + +Some understanding of the factors affecting radio communications will help achieve substantially better service, faster transmission, over a greater range with your devices. Here, we'll attempt to provide a top-level set of guidance for use and aerial selection, how to test the aerials, and a set of resources for further research and plenty of opportunity for going deeper. + +The Meshtastic devices (of various flavours) lend themselves to experimentation, not only because you can replace their aerials, but also because of their mesh operation. All nodes will, without alteration, relay communications from any other members of the mesh around obstacles and over greater distances. The cost of aerial investment should be weighed against investment in additional low-cost nodes. + +:::caution +While the LoRa devices we are using for Meshtastic are relatively low power radios, care should be taken _not_ to operate any radio transmission device without an aerial or with a poorly matched aerial. Un-transmitted radio signal reflected back to the transmitter can damage the device. +::: + +The information collected here is by no means definitive, and necessarily abbreviated (it's a huge topic). + +## Discussion + +To comment on / join in antenna range [Meshtastic discourse](https://meshtastic.discourse.group/t/antenna-improved-range/227/35?u=sens8tion) + +There, you will also find reference to Meshtastic range achievements, aerial recommendations (note we've stopped short of making specific supplier aerial recommendations in this wiki). diff --git a/website/docs/hardware/antenna/non-aerial.md b/website/docs/hardware/antenna/non-aerial.md new file mode 100644 index 00000000..5d209b74 --- /dev/null +++ b/website/docs/hardware/antenna/non-aerial.md @@ -0,0 +1,24 @@ +--- +id: non-aerial +title: Non-aerial factors affecting transmission +sidebar_label: Non-aerial factors +slug: /hardware/non-aerial +--- + +Unless you're using your devices in a vacuum with clear line of sight between aerials: +- Weather (temperature, humidity & air pressure), +- Transmission power, spreading and other associated channel factors, +- Number of nodes within reach in the mesh (affects retries consequent duty cycle hit), +- Absorption by materials (with varying degrees attenuation, by material and depth), +- Reflection off surfaces (and channeled through material tunnels, including warm / cold air tunnels commonly present in the atmosphere), +- Diffraction around obstacles (over forests and around corners). + +### Environmental + +For a bit of light reading on environmental research: +- [RF attentuation in vegetation](https://www.itu.int/dms_pubrec/itu-r/rec/p/R-REC-P.833-9-201609-I!!PDF-E.pdf) (yes really); if you wander through the woods wondering how your RF is bouncing off leaves dependent on their variety, and wind speed … well you do, now. +- [RF attentuation with various building materials](https://www.ofcom.org.uk/__data/assets/pdf_file/0016/84022/building_materials_and_propagation.pdf). +- This one by ITU again is very detailed in its [analysis of the drivers of attenuation](https://www.itu.int/dms_pubrec/itu-r/rec/p/R-REC-P.2040-1-201507-I!!PDF-E.pdf) (I wasn’t aware that all EMF radiation exhibits reflection / transmission characteristics akin to light hitting a material boundary. So, depending on the angle of incidence, material and the EMF wavelength, it will be reflected and / or transmitted through). +- These RF bands are also made more [noisy by adjacent LTE](https://www.ofcom.org.uk/__data/assets/pdf_file/0023/55922/lte-coexistence.pdf) + +In summary - wavelengths in Europe fair well in plain sight, curve over not-so-tall obstacles (including trees), reflect of surfaces at low angles of incidence. They go through humans without much attenuation; but not brick or stone or anything much above glass / kevlar. Oh, and don’t sit under an LTE tower and expect it to be plain sailing. diff --git a/website/docs/hardware/antenna/resources.md b/website/docs/hardware/antenna/resources.md new file mode 100644 index 00000000..de021f25 --- /dev/null +++ b/website/docs/hardware/antenna/resources.md @@ -0,0 +1,46 @@ +--- +id: resources +title: Antenna resources +sidebar_label: Resources +slug: /hardware/resources +--- + + +### Coverage prediction + +* [Tower Coverage.com](https://www.towercoverage.com/) + * Commercial but has free options + + +* [HeyWhat'sThat](http://www.heywhatsthat.com/) + * Free with path profiling options + + +* [Radio Mobile Online](https://www.ve2dbe.com/rmonline_s.asp) + * Radio Mobile Online is a radio wave propagation prediction tool dedicated to amateur radio + + +### RF Tools + +* [Times Microwave Systems](https://www.timesmicrowave.com/calculator/?Product=RG-6&RunLength=10&Frequency=868) + * Coaxial Cable Attenuation & Power Handling Calculator + + +* [Solwise Link Budget Calculator](https://www.solwise.co.uk/link-budget.htm) + * Predict the received signal strength + + +### Antenna designs + +* [1/4 Wave Ground Plane Antenna Calculator](https://m0ukd.com/calculators/quarter-wave-ground-plane-antenna-calculator/) + + +* [Quadrifilar helicoidal antenna calculator](https://jcoppens.com/ant/qfh/calc.en.php) + + +* [Building an 868/915 MHz co-linear antenna tutorial](https://www.youtube.com/watch?v=1_1LxuOngHs) + * [868 Mhz antenna schematic PDF](https://github.com/IRNAS/ttn-irnas-gw/blob/master/Collinear868MHzLoRaantenna.PDF) + * [915 Mhz antenna schematic PDF](https://github.com/IRNAS/ttn-irnas-gw/blob/master/CollinearLoRaantenna915MHzIRNAS.PDF) + + +* [NEC based antenna modeler and optimizer](https://www.qsl.net/4nec2/) \ No newline at end of file diff --git a/website/docs/hardware/antenna/testing.md b/website/docs/hardware/antenna/testing.md new file mode 100644 index 00000000..6ac970dc --- /dev/null +++ b/website/docs/hardware/antenna/testing.md @@ -0,0 +1,33 @@ +--- +id: antenna-testing +title: Antenna testing +sidebar_label: Testing +--- + +Testing of antennas can be both simple and complex. At its simplest, testing involves sending messages from different locations and seeing which ones are received and then comparing the results against other antennas. This ranges upto using expensive test chambers and equipment to measure the signal strength, gain and radiation patterns. However, it seems that a reasonable job can be done with cheaper methods. + +## Range testing + +As mentioned, while stating the obvious, the simplest way of performing test is: +- Walk around with a radio sending messages, +- For each message, note location and whether 'ack' ticks are received, +- Also note reported signal strengths, +- Change aerials, repeat & contrast. + +:::note +The [range test plugin](/docs/software/plugins/range-test-plugin) has been designed for exactly this purpose. It allows one node to transmit a frequent message, and another node to record which messages were received. This data is saved and can be imported to applications such as Google Earth. +::: + +On the topic of testing - performing your own testing and providing feedback is the lifeblood of Meshtastic and OpenSource projects. + +## Signal strength testing + +Real world testing is also discussed by Andreas Speiss (the 'guy with the Swiss accent') in his [tutorial](https://www.youtube.com/watch?v=J3PBL9oLPX8). He has written [code](https://github.com/SensorsIot/Antenna-Tester) for testing antennas using two Lora32 V1 boards to compare how different antennas behave. + +Here are a [couple](https://medium.com/home-wireless/testing-lora-antennas-at-915mhz-6d6b41ac8f1d) of [excellent](https://medium.com/home-wireless/testing-and-reviewing-lora-antennas-5b37dfa594a3) aerial comparisons. Their utility goes beyond the specific aerials tested, giving insight into: +- Aerial types & their characteristics, +- Testing approaches. + +## Antenna matching & vector network analysers + +One of the first things to ensure is that the antenna you have is tuned to the frequency that you are using. A lot of cheap antennas come labeled with an incorrect working frequency, and this will immediately reduce the emittted signal stregth. A Vector Network Analyser (VNA) can be used to ensure that the antenna is appropriately matched to the tranmission circuit, ensuring that it is operating at the correct impeadance and has a low level of power reflected back from the antenna to the transmitter at the desired transmission frequency. Andeas Speiss (the 'guy with the Swiss accent') gives a great explanation of [how to use Vector Network Analysers](https://www.youtube.com/watch?v=ZpKoLvqOWyc) to correctly tune your antennas, as well as a more [in depth tutorial of how to use VNAs](https://www.youtube.com/watch?v=_pjcEKQY_Tk). It is important to remember however, that VNAs can only tell you if the antenna is well matched, not how well it is transmitting. A 50 ohm resistor across the transmitter output would show as ideally matched, but it would be useless at transmitting a signal. There are a number of VNAs now available for less than $100, making this no longer out of reach for most hobbiests unlike expensive spectrum analysers. diff --git a/website/docs/software/plugins/plugin-api.md b/website/docs/software/plugins/plugin-api.md new file mode 100644 index 00000000..e69de29b diff --git a/website/sidebars.js b/website/sidebars.js index bbdedc4e..6df0486e 100644 --- a/website/sidebars.js +++ b/website/sidebars.js @@ -136,7 +136,15 @@ module.exports = { ], }, "hardware/behaviour", - "hardware/antenna", + { + "Antennas": [ + "hardware/antenna/antenna", + "hardware/antenna/aerials", + "hardware/antenna/non-aerial", + "hardware/antenna/antenna-testing" + "hardware/antenna/resources", + ], + }, ], Developers: [ "developers/overview", From b6d15e27a436f92b590b5ba43e371157f30ecd29 Mon Sep 17 00:00:00 2001 From: apt105 <73254487+apt105@users.noreply.github.com> Date: Sun, 9 May 2021 14:52:02 +0100 Subject: [PATCH 2/3] Update sidebars.js --- website/sidebars.js | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/website/sidebars.js b/website/sidebars.js index 6df0486e..b00551e2 100644 --- a/website/sidebars.js +++ b/website/sidebars.js @@ -141,7 +141,7 @@ module.exports = { "hardware/antenna/antenna", "hardware/antenna/aerials", "hardware/antenna/non-aerial", - "hardware/antenna/antenna-testing" + "hardware/antenna/antenna-testing", "hardware/antenna/resources", ], }, From b7352f76c27d81c18bfba96c338609a42d6efe1a Mon Sep 17 00:00:00 2001 From: apt105 <73254487+apt105@users.noreply.github.com> Date: Sun, 9 May 2021 15:03:35 +0100 Subject: [PATCH 3/3] Small fixes --- website/docs/hardware/antenna/antenna.md | 2 +- website/docs/hardware/antenna/non-aerial.md | 4 ++-- website/docs/hardware/antenna/resources.md | 2 ++ website/docs/hardware/antenna/testing.md | 4 +++- 4 files changed, 8 insertions(+), 4 deletions(-) diff --git a/website/docs/hardware/antenna/antenna.md b/website/docs/hardware/antenna/antenna.md index e1b7c7f9..4398adfb 100644 --- a/website/docs/hardware/antenna/antenna.md +++ b/website/docs/hardware/antenna/antenna.md @@ -1,7 +1,7 @@ --- id: antenna title: Antennas -sidebar_label: Antennas +sidebar_label: Overview slug: /hardware/antenna --- diff --git a/website/docs/hardware/antenna/non-aerial.md b/website/docs/hardware/antenna/non-aerial.md index 5d209b74..299d784f 100644 --- a/website/docs/hardware/antenna/non-aerial.md +++ b/website/docs/hardware/antenna/non-aerial.md @@ -5,7 +5,7 @@ sidebar_label: Non-aerial factors slug: /hardware/non-aerial --- -Unless you're using your devices in a vacuum with clear line of sight between aerials: +Unless you're using your devices in a vacuum with clear line of sight between aerials the following will have an affect: - Weather (temperature, humidity & air pressure), - Transmission power, spreading and other associated channel factors, - Number of nodes within reach in the mesh (affects retries consequent duty cycle hit), @@ -13,7 +13,7 @@ Unless you're using your devices in a vacuum with clear line of sight between ae - Reflection off surfaces (and channeled through material tunnels, including warm / cold air tunnels commonly present in the atmosphere), - Diffraction around obstacles (over forests and around corners). -### Environmental +### Environmental factors For a bit of light reading on environmental research: - [RF attentuation in vegetation](https://www.itu.int/dms_pubrec/itu-r/rec/p/R-REC-P.833-9-201609-I!!PDF-E.pdf) (yes really); if you wander through the woods wondering how your RF is bouncing off leaves dependent on their variety, and wind speed … well you do, now. diff --git a/website/docs/hardware/antenna/resources.md b/website/docs/hardware/antenna/resources.md index de021f25..ef0ffd3f 100644 --- a/website/docs/hardware/antenna/resources.md +++ b/website/docs/hardware/antenna/resources.md @@ -29,6 +29,8 @@ slug: /hardware/resources * [Solwise Link Budget Calculator](https://www.solwise.co.uk/link-budget.htm) * Predict the received signal strength +* [Amateur Radio Toolkit](https://play.google.com/store/apps/details?id=com.daveyhollenberg.amateurradiotoolkit) + * Android app with lots of antenna information ### Antenna designs diff --git a/website/docs/hardware/antenna/testing.md b/website/docs/hardware/antenna/testing.md index 6ac970dc..f4d8abb0 100644 --- a/website/docs/hardware/antenna/testing.md +++ b/website/docs/hardware/antenna/testing.md @@ -30,4 +30,6 @@ Here are a [couple](https://medium.com/home-wireless/testing-lora-antennas-at-91 ## Antenna matching & vector network analysers -One of the first things to ensure is that the antenna you have is tuned to the frequency that you are using. A lot of cheap antennas come labeled with an incorrect working frequency, and this will immediately reduce the emittted signal stregth. A Vector Network Analyser (VNA) can be used to ensure that the antenna is appropriately matched to the tranmission circuit, ensuring that it is operating at the correct impeadance and has a low level of power reflected back from the antenna to the transmitter at the desired transmission frequency. Andeas Speiss (the 'guy with the Swiss accent') gives a great explanation of [how to use Vector Network Analysers](https://www.youtube.com/watch?v=ZpKoLvqOWyc) to correctly tune your antennas, as well as a more [in depth tutorial of how to use VNAs](https://www.youtube.com/watch?v=_pjcEKQY_Tk). It is important to remember however, that VNAs can only tell you if the antenna is well matched, not how well it is transmitting. A 50 ohm resistor across the transmitter output would show as ideally matched, but it would be useless at transmitting a signal. There are a number of VNAs now available for less than $100, making this no longer out of reach for most hobbiests unlike expensive spectrum analysers. +One of the first things to ensure is that the antenna you have is tuned to the frequency that you are using. A lot of cheap antennas come labeled with an incorrect working frequency, and this will immediately reduce the emittted signal stregth. A Vector Network Analyser (VNA) can be used to ensure that the antenna is appropriately matched to the tranmission circuit, ensuring that it is operating at the correct impeadance and has a low level of power reflected back from the antenna to the transmitter at the desired transmission frequency. + +Andeas Speiss also gives a great explanation of [how to use Vector Network Analysers](https://www.youtube.com/watch?v=ZpKoLvqOWyc) to correctly tune your antennas, as well as a more [in depth tutorial of how to use VNAs](https://www.youtube.com/watch?v=_pjcEKQY_Tk). It is important to remember however, that VNAs can only tell you if the antenna is well matched, not how well it is transmitting. A 50 ohm resistor across the transmitter output would show as ideally matched, but it would be useless at transmitting a signal. There are a number of VNAs now available for less than $100, making this no longer out of reach for most hobbiests unlike expensive spectrum analysers.