diff --git a/docs/getting-started/flashing-firmware/esp32/cli-script.mdx b/docs/getting-started/flashing-firmware/esp32/cli-script.mdx
index 51bbade3..6db52e02 100644
--- a/docs/getting-started/flashing-firmware/esp32/cli-script.mdx
+++ b/docs/getting-started/flashing-firmware/esp32/cli-script.mdx
@@ -18,7 +18,7 @@ Before you flash your device start by verifying connectivity with the device bei
 :::note
 The [T-Beam 0.7](/docs/hardware/devices/tbeam#t-beam---v07) board is an earlier version of the T-Beam board, and due to changes in the design in subsequent iterations this board uses a specific firmware file different from the other T-Beam boards.
 
-`firmware-tbeam0.7-1.x.x.bin` is the correct firmware. `firmware-tbeam-1.x.x.bin` is incompatible. For all other [T-Beam](/docs/hardware/devices/tbeam) boards `firmware-tbeam-1.x.x.bin` is the correct selection.
+`firmware-tbeam0.7-X.X.X.xxxxxxx.bin` is the correct firmware. `firmware-tbeam-X.X.X.xxxxxxx.bin` is incompatible. For all other [T-Beam](/docs/hardware/devices/tbeam) boards `firmware-tbeam-X.X.X.xxxxxxx.bin` is the correct selection.
 :::
 
 ## Command Line Interface Instructions
@@ -186,7 +186,7 @@ cd ~/Downloads/firmware/
 Install or Update the device that you have by using the following commands according to your operating system:
 
 :::caution
-Be very careful to install the correct load for your board. In particular the popular 'T-BEAM' radio from TTGO is not called 'TTGO-Lora' (that is a different board). So don't install the 'TTGO-Lora' build on a TBEAM, it won't work correctly.
+Be very careful to install the correct firmware file for your board. In particular, the popular 'T-BEAM' radio from TTGO is not called 'TTGO-Lora' (that is a different board). So don't install the 'TTGO-Lora' build on a TBEAM, it won't work correctly. If you flash the incorrect device firmware, it may appear to successfully complete, yet the device will usually become unresponsive, displaying a blank screen (if equipped). Attempt to flash the correct version. Please note, while these devices are quite resilient and damage is not always likely, there is a possibility of onboard radio and peripheral damage due to incorrect GPIO pin direction.
 :::
 
 <Tabs
@@ -214,12 +214,14 @@ values={[
   </TabItem>
   <TabItem value="macos">
 
+<!-- trunk-ignore(markdownlint/MD024) -->
 #### Install
 
 ```shell title="Command"
 ./device-install.sh -f firmware-BOARD-VERSION.bin
 ```
 
+<!-- trunk-ignore(markdownlint/MD024) -->
 #### Update
 
 ```shell title="Command"
@@ -229,12 +231,14 @@ values={[
   </TabItem>
   <TabItem value="windows">
 
+<!-- trunk-ignore(markdownlint/MD024) -->
 #### Install
 
 ```shell title="Command"
 device-install.bat -f firmware-BOARD-VERSION.bin
 ```
 
+<!-- trunk-ignore(markdownlint/MD024) -->
 #### Update
 
 ```shell title="Command"
@@ -244,17 +248,6 @@ device-update.bat -f firmware-BOARD-VERSION.bin
   </TabItem>
 </Tabs>
 
-### Select Firmware
-
-Browse to the previously downloaded firmware and select the correct firmware based on the board type and frequency.
-
-:::caution
-Be very careful to install the correct load for your board. In particular the popular 'T-BEAM' radio from TTGO is not called 'TTGO-Lora' (that is a different board). So don't install the 'TTGO-Lora' build on a TBEAM, it won't work correctly. If you flash the incorrect firmware: It may appear to flash correctly, but if your device has a screen it might stay blank. On-board radio peripherals might be damaged because of GPIO pin direction, but you should just try to flash with the correct version.
-:::
-
-### Flash Firmware
-
-Select `Flash ESP`. It may take a minute or two. Once complete, "Done! Flashing is complete!" will be shown.
 
 ## Connect and Configure Device