mirror of
https://github.com/meshtastic/meshtastic.git
synced 2024-11-15 18:14:19 -08:00
108 lines
2.7 KiB
Plaintext
108 lines
2.7 KiB
Plaintext
---
|
|
id: test-serial-driver-installation
|
|
title: Test Serial Driver Installation
|
|
sidebar_label: Test Serial Driver Installation
|
|
sidebar_position: 3
|
|
---
|
|
|
|
import Link from "@docusaurus/Link";
|
|
import Tabs from "@theme/Tabs";
|
|
import TabItem from "@theme/TabItem";
|
|
|
|
### Test Serial Driver Installation
|
|
|
|
You can verify that you have a proper data cable (rather than a charge-only type cable) and that the appropriate drivers for your system are installed by performing the following test:
|
|
|
|
<Tabs
|
|
groupId="operating-system"
|
|
defaultValue="linux"
|
|
values={[
|
|
{label: 'Linux', value: 'linux'},
|
|
{label: 'macOS', value: 'macos'},
|
|
{label: 'Windows', value: 'windows'},
|
|
]}>
|
|
<TabItem value="linux">
|
|
|
|
#### Linux
|
|
|
|
1. Connect your Meshtastic device to your USB port
|
|
2. Open a **Terminal** and enter the following command:
|
|
|
|
```shell
|
|
lsusb
|
|
```
|
|
|
|
3. You should see something like:
|
|
|
|
```shell
|
|
ID xxxx:xxxx Silicon Labs CP210x UART Bridge
|
|
# or
|
|
ID xxxx:xxxx QinHeng Electronics USB Single Serial
|
|
# or
|
|
FIXME (WISBLOCK OUTPUT)
|
|
```
|
|
|
|
</TabItem>
|
|
<TabItem value="macos">
|
|
|
|
#### macOS
|
|
|
|
1. Navigate to `Apple Menu > About This Mac > More Info > System Report... > Hardware > USB`.
|
|
2. You should see similar to one of the following entries:
|
|
|
|
- `CP210X USB to UART Bridge Controller`
|
|
- `CH9102 USB to UART Bridge Controller`
|
|
- `WisCore RAK4631 Board`
|
|
- `USB Single Serial`
|
|
|
|
</TabItem>
|
|
<TabItem value="windows">
|
|
|
|
#### Windows
|
|
|
|
1. Navigate to `Device Manager > Ports (COM & LPT)`
|
|
2. You should see similar to one of the following entries:
|
|
|
|
- `Silicon Labs CP210X USB to UART Bridge (COM5)`
|
|
- `Silicon Labs CH9102 USB to UART Bridge (COM5)`
|
|
- `USB-Enhanced-SERIAL CH9102 (COM5)`
|
|
- `USB Serial Device (COM5)`
|
|
|
|
</TabItem>
|
|
</Tabs>
|
|
|
|
:::info
|
|
|
|
If you are unable to see your device:
|
|
|
|
- Make sure that your cable is not only for charging but also for [data transfer](/docs/getting-started#verify-data-cable).
|
|
- It's possible that you need to [reinstall the USB serial driver](/docs/getting-started/serial-drivers).
|
|
|
|
:::
|
|
|
|
## Flash Firmware
|
|
|
|
After completing the previous steps, you can now flash the Meshtastic firmware onto your device. To proceed, select the appropriate device type for your device.
|
|
|
|
<div className="indexCtasBody">
|
|
<div className="split-container">
|
|
<div className="split-item">
|
|
<Link
|
|
className={"button button--outline button--lg cta--button"}
|
|
to={"/docs/getting-started/flashing-firmware/esp32/"}
|
|
>
|
|
Flash ESP32 Firmware
|
|
</Link>
|
|
</div>
|
|
|
|
<div className="split-item">
|
|
<Link
|
|
className={"button button--outline button--lg cta--button"}
|
|
to={"/docs/getting-started/flashing-firmware/nrf52/"}
|
|
>
|
|
Flash nRF52/RP2040 Firmware
|
|
</Link>
|
|
</div>
|
|
</div>
|
|
</div>
|