Fixes https://github.com/prometheus/prometheus/issues/1401
This remove the last (and in fact bogus) use of BoundaryValues.
Thus, a whole lot of unused (and arguably sub-optimal / ugly) code can
be removed here, too.
This will fix issue #1035 and will also help to make issue #1264 less
bad.
The fundamental problem in the current code:
In the preload phase, we quite accurately determine which chunks will
be used for the query being executed. However, in the subsequent step
of creating series iterators, the created iterators are referencing
_all_ in-memory chunks in their series, even the un-pinned ones. In
iterator creation, we copy a pointer to each in-memory chunk of a
series into the iterator. While this creates a certain amount of
allocation churn, the worst thing about it is that copying the chunk
pointer out of the chunkDesc requires a mutex acquisition. (Remember
that the iterator will also reference un-pinned chunks, so we need to
acquire the mutex to protect against concurrent eviction.) The worst
case happens if a series doesn't even contain any relevant samples for
the query time range. We notice that during preloading but then we
will still create a series iterator for it. But even for series that
do contain relevant samples, the overhead is quite bad for instant
queries that retrieve a single sample from each series, but still go
through all the effort of series iterator creation. All of that is
particularly bad if a series has many in-memory chunks.
This commit addresses the problem from two sides:
First, it merges preloading and iterator creation into one step,
i.e. the preload call returns an iterator for exactly the preloaded
chunks.
Second, the required mutex acquisition in chunkDesc has been greatly
reduced. That was enabled by a side effect of the first step, which is
that the iterator is only referencing pinned chunks, so there is no
risk of concurrent eviction anymore, and chunks can be accessed
without mutex acquisition.
To simplify the code changes for the above, the long-planned change of
ValueAtTime to ValueAtOrBefore time was performed at the same
time. (It should have been done first, but it kind of accidentally
happened while I was in the middle of writing the series iterator
changes. Sorry for that.) So far, we actively filtered the up to two
values that were returned by ValueAtTime, i.e. we invested work to
retrieve up to two values, and then we invested more work to throw one
of them away.
The SeriesIterator.BoundaryValues method can be removed once #1401 is
fixed. But I really didn't want to load even more changes into this
PR.
Benchmarks:
The BenchmarkFuzz.* benchmarks run 83% faster (i.e. about six times
faster) and allocate 95% fewer bytes. The reason for that is that the
benchmark reads one sample after another from the time series and
creates a new series iterator for each sample read.
To find out how much these improvements matter in practice, I have
mirrored a beefy Prometheus server at SoundCloud that suffers from
both issues #1035 and #1264. To reach steady state that would be
comparable, the server needs to run for 15d. So far, it has run for
1d. The test server currently has only half as many memory time series
and 60% of the memory chunks the main server has. The 90th percentile
rule evaluation cycle time is ~11s on the main server and only ~3s on
the test server. However, these numbers might get much closer over
time.
In addition to performance improvements, this commit removes about 150
LOC.
The new implementation detects the start and end of a series by
looking at the average sample interval within the range. If the first
(last) sample in the range is more than 1.1*interval distant from the
beginning (end) of the range, it is considered the first (last) sample
of the series as a whole, and extrapolation is limited to half the
interval (rather than all the way to the beginning (end) of the
range). In addition, if the extrapolated starting point of a counter
(where it is zero) is within the range, it is used as the starting
point of the series.
Fixes#581
This change is breaking, use increase() instead.
I'm not cleaning up the function in this PR, as my solution to #581 will
rewrite and simplify increase/rate/delta.
irate is a rate function that only looks at the most
recent two data points, and calucaltes a per-second value
from that. This produces much more granular graphs for
fast moving data, and works sanely across many scrape intervals.
It doesn't do so well for slowly moving data.
Currently the only way to convert a scalar to a vector is to
use absent(), which isn't very clean. This adds a vector()
function that's the inverse of scalar() and lets your optionally
set labels.
Example usage would be
vector(time() % 86400) < 3600
to filter to only the first hour of the day.
This calculates how much a counter increases over
a given period of time, which is the area under the curve
of it's rate.
increase(x[5m]) is equivilent to rate(x[5m]) * 300.
This copies the evaluation logic from the current rules/ package.
The new engine handles the execution process from query string to final result.
It provides query timeout and cancellation and general flexibility for
future changes.
functions.go: Add evaluation implementation. Slight changes to in/out data but
not to the processing logic.
quantile.go: No changes.
analyzer.go: No changes.
engine.go: Actually new part. Mainly consists of evaluation methods
which were not changed.
setup_test.go: Copy of rules/helpers_test.go to setup test storage.
promql_test.go: Copy of rules/rules_test.go.
This commit creates a (so far unused) package. It contains the a custom
lexer/parser for the query language.
ast.go: New AST that interacts well with the parser.
lex.go: Custom lexer (new).
lex_test.go: Lexer tests (new).
parse.go: Custom parser (new).
parse_test.go: Parser tests (new).
functions.go: Changed function type, dummies for parser testing (barely changed/dummies).
printer.go: Adapted from rules/ and adjusted to new AST (mostly unchanged, few additions).
