mirror of
https://github.com/meshtastic/meshtastic.git
synced 2024-12-28 23:19:47 -08:00
293 lines
7.5 KiB
Markdown
293 lines
7.5 KiB
Markdown
---
|
|
id: flashing-esp32
|
|
title: Flashing ESP32 devices firmware
|
|
sidebar_label: ESP32 devices
|
|
---
|
|
|
|
import Tabs from '@theme/Tabs';
|
|
import TabItem from '@theme/TabItem';
|
|
|
|
## Prerequisites
|
|
|
|
### Check Data Cable
|
|
|
|
Plug your device into your computer using a USB cable and then do the following:
|
|
:::important
|
|
You may need to install a driver from Silicon Labs for the [CP210X USB to UART bridge](https://www.silabs.com/products/development-tools/software/usb-to-uart-bridge-vcp-drivers)
|
|
|
|
Some newer boards may require the drivers for the [CH9102](http://www.wch.cn/downloads/CH343SER_ZIP.html) or [Direct Download](https://github.com/Xinyuan-LilyGO/CH9102_Driver) for Windows 7.
|
|
:::
|
|
|
|
<Tabs
|
|
groupId="operating-system"
|
|
defaultValue="linux"
|
|
values={[
|
|
{label: 'Linux', value: 'linux'},
|
|
{label: 'macOS', value: 'macos'},
|
|
{label: 'Windows', value: 'windows'},
|
|
]}>
|
|
<TabItem value="linux">
|
|
|
|
> Connect your Meshtastic device to your USB port, open a `Terminal` and enter the following command:
|
|
>
|
|
> ```bash
|
|
> lsusb
|
|
> ```
|
|
>
|
|
> You should see something like: `ID 10c4:ea60 Silicon Labs CP210x UART Bridge` for CP210X or `ID 1a86:55d4 QinHeng Electronics USB Single Serial` for CH9102
|
|
|
|
</TabItem>
|
|
<TabItem value="macos">
|
|
|
|
> Navigate to `Apple Menu > About This Mac > System Report... > Hardware > USB`.
|
|
> You should see something like `CP210X USB to UART Bridge Controller`. If not download the appropriate drivers
|
|
|
|
</TabItem>
|
|
<TabItem value="windows">
|
|
|
|
> Navigate to `Device Manager > Ports (COM & LPT)`. You should see something like `Silicon Labs CP210X USB to UART Bridge (COM5)`. If not download the appropriate drivers
|
|
|
|
</TabItem>
|
|
</Tabs>
|
|
|
|
### Download Latest Firmware
|
|
|
|
Firmware can be downloaded from the [Firmware](/firmware) page. Your initial installation has to happen over USB from your Mac, Windows, or Linux PC. Once our software is installed, all future software updates happen over Bluetooth from your phone.
|
|
|
|
:::note
|
|
The [T-Beam 0.7](/docs/hardware/supported/tbeam#t-beam---v07) board is an earlier version of the T-Beam board, and due to changes in the design in subsequent iterations this board uses a specific firmware file different from the other T-Beam boards.
|
|
|
|
`firmware-tbeam0.7-1.x.x.bin` is the correct firmware. `firmware-tbeam-1.x.x.bin` is incompatible. For all other [T-Beam](/docs/hardware/supported/tbeam) boards `firmware-tbeam-1.x.x.bin` is the correct selection.
|
|
:::
|
|
|
|
## Command Line Interface Instructions
|
|
|
|
<Tabs
|
|
groupId="operating-system"
|
|
defaultValue="linux"
|
|
values={[
|
|
{label: 'Linux', value: 'linux'},
|
|
{label: 'macOS', value: 'macos'},
|
|
{label: 'Windows', value: 'windows'},
|
|
]}>
|
|
<TabItem value="linux">
|
|
|
|
### Install Prerequisite Software
|
|
|
|
> Check if you have `python3` and `pip` installed with the following command
|
|
>
|
|
> ```bash
|
|
> python3 --version
|
|
> pip3 --version
|
|
> ```
|
|
>
|
|
> If `python3` is not installed, install with
|
|
>
|
|
> ```bash
|
|
> sudo apt-get update
|
|
> sudo apt-get install python3
|
|
> ```
|
|
>
|
|
> If `pip` is not installed, install with
|
|
>
|
|
> ```bash
|
|
> sudo apt-get install python3-pip
|
|
> ```
|
|
|
|
### Install `esptool`
|
|
|
|
> ```bash
|
|
> pip3 install --upgrade esptool
|
|
> ```
|
|
|
|
</TabItem>
|
|
<TabItem value="macos">
|
|
|
|
### Install Prerequisite Software
|
|
|
|
> OS X comes with `Python 2.7` installed, but not `pip`. The following uses Homebrew to install `python3` which includes `pip3`. On MacOS you will use `pip3` instead > of `pip`.
|
|
|
|
:::note
|
|
Check if you have Homebrew installed with the following command
|
|
|
|
```bash
|
|
brew -v
|
|
```
|
|
|
|
If it's not installed, follow the instructions on the [Homebrew website](https://brew.sh) before continuing.
|
|
:::
|
|
|
|
> Check if you have `python3` and `pip` installed with the following command
|
|
>
|
|
> ```bash
|
|
> python3 --version
|
|
> pip3 --version
|
|
> ```
|
|
>
|
|
> If `python3` is not installed, install with
|
|
> Install Python3
|
|
>
|
|
> ```bash
|
|
> brew install python3
|
|
> ```
|
|
>
|
|
> Confirm `pip3` was installed alongside `python3`
|
|
>
|
|
> ```bash
|
|
> pip3 -v
|
|
> ```
|
|
|
|
### Install `esptool`
|
|
|
|
> ```bash
|
|
> pip3 install --upgrade esptool
|
|
> ```
|
|
|
|
</TabItem>
|
|
<TabItem value="windows">
|
|
|
|
> - Download and install [Python](https://www.python.org/). When installing, make sure to click `Add Python X.Y to PATH`.
|
|
> - Download and install [Gitbash](https://gitforwindows.org/) (or other appropriate shell) and run all subsequent commands from that shell.
|
|
|
|
:::note
|
|
Confirm installation of `python` & `pip` with the following commands.
|
|
|
|
```bash
|
|
py --version
|
|
```
|
|
|
|
```bash
|
|
pip --version
|
|
```
|
|
|
|
:::
|
|
|
|
### Install `esptool`
|
|
|
|
> ```bash
|
|
> pip install --upgrade esptool
|
|
> ```
|
|
|
|
</TabItem>
|
|
</Tabs>
|
|
|
|
### Confirm Communication With Chip
|
|
|
|
Connect the radio to your computer using a data USB cable. Confirm your device is talking to your computer using the following command:
|
|
|
|
:::important
|
|
On windows, you must explicitly declare esptools as a .py script. Use `esptools.py chip_id`.
|
|
:::
|
|
|
|
```bash title="Command"
|
|
esptool chip_id
|
|
```
|
|
|
|
```bash title="Expected Output"
|
|
# You should see a result similar to this:
|
|
mydir$ esptool chip_id
|
|
esptool.py v2.6
|
|
Found 2 serial ports
|
|
Serial port /dev/ttyUSB0
|
|
Connecting....
|
|
Detecting chip type... ESP32
|
|
Chip is ESP32D0WDQ6 (revision 1)
|
|
Features: WiFi, BT, Dual Core, 240MHz, VRef calibration in efuse, Coding Scheme None
|
|
MAC: 24:6f:28:b5:36:71
|
|
Uploading stub...
|
|
Running stub...
|
|
Stub running...
|
|
Warning: ESP32 has no Chip ID. Reading MAC instead.
|
|
MAC: 24:6f:28:b5:36:71
|
|
Hard resetting via RTS pin...
|
|
```
|
|
|
|
### Navigate to Firmware
|
|
|
|
`cd` into the directory where you unzipped the latest release. For example:
|
|
|
|
```bash title="Example"
|
|
cd ~/Downloads/firmware/
|
|
```
|
|
|
|
### Install/Update Firmware
|
|
|
|
Install or Update the device that you have by using the following commands according to your operating system:
|
|
|
|
:::caution
|
|
Be very careful to install the correct load for your board. In particular the popular 'T-BEAM' radio from TTGO is not called 'TTGO-Lora' (that is a different board). So don't install the 'TTGO-Lora' build on a TBEAM, it won't work correctly.
|
|
:::
|
|
|
|
<Tabs
|
|
groupId="operating-system"
|
|
defaultValue="linux"
|
|
values={[
|
|
{label: 'Linux', value: 'linux'},
|
|
{label: 'macOS', value: 'macos'},
|
|
{label: 'Windows', value: 'windows'},
|
|
]}>
|
|
<TabItem value="linux">
|
|
|
|
#### Install
|
|
|
|
> ```bash title="Command"
|
|
> ./device-install.sh -f firmware-BOARD-VERSION.bin
|
|
> ```
|
|
|
|
#### Update
|
|
|
|
> ```bash title="Command"
|
|
> ./device-update.sh -f firmware-BOARD-VERSION.bin
|
|
> ```
|
|
|
|
</TabItem>
|
|
<TabItem value="macos">
|
|
|
|
#### Install
|
|
|
|
> ```bash title="Command"
|
|
> ./device-install.sh -f firmware-BOARD-VERSION.bin
|
|
> ```
|
|
|
|
#### Update
|
|
|
|
> ```bash title="Command"
|
|
> ./device-update.sh -f firmware-BOARD-VERSION.bin
|
|
> ```
|
|
|
|
</TabItem>
|
|
<TabItem value="windows">
|
|
|
|
#### Install
|
|
|
|
> ```bash title="Command"
|
|
> ./device-install.bat -f firmware-BOARD-VERSION.bin
|
|
> ```
|
|
|
|
#### Update
|
|
|
|
> ```bash title="Command"
|
|
> ./device-update.bat -f firmware-BOARD-VERSION.bin
|
|
> ```
|
|
|
|
</TabItem>
|
|
</Tabs>
|
|
|
|
### Select Firmware
|
|
|
|
Browse to the previously downloaded firmware and select the correct firmware based on the board type and frequency.
|
|
|
|
:::caution
|
|
Be very careful to install the correct load for your board. In particular the popular 'T-BEAM' radio from TTGO is not called 'TTGO-Lora' (that is a different board). So don't install the 'TTGO-Lora' build on a TBEAM, it won't work correctly. If you flash the incorrect firmware: It may appear to flash correctly, but if your device has a screen it might stay blank. On-board radio peripherals might be damaged because of GPIO pin direction, but you should just try to flash with the correct version.
|
|
:::
|
|
|
|
### Flash Firmware
|
|
|
|
Select `Flash ESP`. It may take a minute or two. Once complete, "Done! Flashing is complete!" will be shown.
|
|
|
|
## Over the Air Update Instructions
|
|
|
|
OTA updates are only currently available on Android.
|
|
|
|
<!--- TODO --->
|